Day 5 The First and Second Coat

 May 15, 2021

 Ollie Weiss 

Day 4

Friday, May 14, 2021

10:10pm

Hours spent: 9:00am - 4pm 

I made it into the shop on the earlier side this morning and finished up a little bit of sanding to ensure the bull was smooth. After reading the directions on the back of the paint can and watching a quick video on youtube, I felt pretty confident in my boat painting abilities and got right to work. I thinned the paint 10% like the directions said and "rolled and tipped" the paint to get rid of bubbles and patterns left by the roller. After about an hour of painting, I was covered in little drips and drops, but the boat looked really Good. 

After hand planning down the Inwals and working on the Console for the majority of the day, the paint was finally dry enough to tape over. I wanted to put one more coat of bottom paint on the boat and was able to tape over the grey primer and roll on another coat of Seafoam Bottom paint. 





Comments

Post a Comment

Popular posts from this blog

Day 3 Waterline calculations and console work

Image
Ollie Weiss  Day 3  Wednesday, May 12, 2021  10:15pm Hours spent: 9:45am - 3:00pm My day began at 9:45 am, mixing grey two a part epoxy primer with the hopes it would magically dry faster than expected, and I would be able to sand and continue along. However, that was not the case; after watching paint dry from different angles for almost an hour, I decided to work on the Console.   Opposed to using glue or screws to hold pieces together, I drill small aligning holes on each board and tie them together with copper wire. The tension from the copper wires allows me to run a thickened epoxy fillet along with the corner bonding the pieces together once it has time to cure. I spent a few hours this morning stitching the marine grade plywood together and running the first epoxy filletts along the corners.    Into the afternoon, I realized that the waterline work was going to be much harder than I originally thought. Most boats that spend the majority of...
Read more

Day 1 May 10, 2021

Image
Ollie Weiss  Monday, May 10, 2021  10:10 pm  Follow along on Instagram @TheSkiffBuild    Over the next two weeks, I will be trying my best to finish up the boat I have been working on for some time now. For anyone reading this that is not aware, I have spent the last three years cutting, assembling, fiberglassing, and soon to be painting a 15ft Flat Bottom Skiff. The boat's design and instructions come from Chesapeake Light Craft, and many of the materials I will be using are from Total Boat.       My day started at 10:00 am, where I began preparing to glue up the port and starboard gunwale doublers. I began by sanding both of the large pieces with 120 grit sandpaper until they were smooth. Once finished, I test fit the pieces on the boat's sides and drilled pilot holes that I will later use to hold the pieces together.  After minor tweaks, I had everything sitting the way I wanted It. I took the precautions to tape off the surrounding a...
Read more

Day 2 - Sanding and Primer

Image
  Ollie Weiss  Tuesday, May 11, 2021  Day 2  9:00 am  - 4:35 pm  Yesterday morning started with me removing various clamps from the boat that were holding the gunwale doublers in place overnight. The glue-up went great and did not leave much of a mess, so I was able to quickly sand the pieces with an orbital sander and a 120 grid disk. In no time at all, I had the doublers sanded and taped off.  For the remainder of the day, I focused on prepping the boat for paint. I will be using various colors to protect the hull from moisture and started with the Total Protect 3:1 Epoxy barrier primer from Total Boat. This paint will act as a barrier coat between the fiberglass and paint, keeping out all the moisture, especially underneath the waterline.  I gave the entire boat a once over with 120 grit disks making sure it was as flat as I could get it, before whipping off the boat with a tack cloth. After the hull was clean, I mixed up the Epoxy primer and r...
Read more